AEG 99852G-M Instrukcja Użytkownika

B 99852GUser ManualHobGB

10Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.

11Instructions for the InstallerEngineers technical dataBURNER ULTRA-RAPID SEMI-RAPID AUXILIARY(triple crown) (medium) (small)POSITION MA X MIN MA X M

12700 mm400 mm400 mm100 mm50 mm50 mm55 mm700 mm400 mm100 mm400 mm50 mm50 mm55 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOV

13InstallationImportantAny gas installation must be carried out by a GAS SAFE REGISTER installer.The manufacturer will not accept liability, should th

14Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed above

15ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must be taken indesigning th

16Fitting the hob to the worktopBefore fitting the hob into the cut out, an adhesive seal must be fitted to the undersideoutside edge of the hob. It i

17Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

18Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity

19Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

2 Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer C

20A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale andadjust zero if necessary.— Test leads fro

21Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

22CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting. Todo this, follow the procedure below.1)

23Conversion from Natural Gas to LPGIMPORTANTThe replacement/conversion of the gas hob should only be undertaken by acompetent person.It is important

24Service and Spare PartsBefore calling out an engineer, please ensure you have read the details under the heading“Something not working”When you cont

25Guarantee ConditionsWe, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part the

26European GuaranteeThis appliance is guaranteed by Electrolux in each of the countries listed at the back of thisuser manual, for the period specifie

27

35686-0204 08/10 R.C Grafiche MDM - Forlìwww.aeg-electrolux.co.ukAEG Haugeräte GmbHPostfach 1036D-90327 Nürnberghttp://www.aeg.hausgeraete.de

3zDo not use this hob if it is in contact with water. Do not operate the hob with wet hands.zEnsure the control knobs are in the ‘OFF’ position when n

4This appliance is manufactured according to the following EEC directives:2006/95 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC, current edition.Guide to U

51. Hob Top2. Semi-rapid Burners3. Auxiliary Burner4. Ultra-rapid Burner (triple crown)5. Control knobsDescription of the HobINSTALLATIONAny gas insta

6Hob burnersTo light a burner:z Push in the relevant control knob and turn it tomaximum position.z Upon ignition, keep the knob pushed down about5 sec

7Fig. 2Using the Wok StandA wok stand is provided to enable you to use around bottomed wok on the hob. The wok standmust only be used on the central b

8Maintenance and CleaningBefore any maintenance or cleaningcan be carried out, you mustDISCONNECT the hob from theelectricity supply.The hob is best c

9Pan SupportsTo keep the pan supports in the correct position, they are mounted on metal pinslocated in the back of the hob. After cleaning the hob, e