AEG BH8.04 Instrukcja Użytkownika Strona 1

AUS ERFAHRUNG GUT34942G/35940G/35941G/35944GGas hobTable de cuissonKochmuldeGaskookplaatPiano di cotturaOperating and Installation Instructions GBNoti

10Service and Spare PartsWhen you contact the Service Centre, they will need the followinginformation:1. Your name, address and post code.2. Your te

11Guarantee ConditionsAEG offer the following guarantee to the first purchaser of this appliance.1. The guarantee is valid for 12 months commencing wh

12OVERALL DIMENSIONS Width: 860 mm.Depth: 500 mm.Height: 88 mm.Weight: 8 Kg.CUT OUT DIMENSIONS Width: 830 mm.Depth: 470 mm.Thickness: 30 mm.SUPPLY CO

13Burner Dia. Tap By-pass Tap colour1/100 mmAuxiliary 28 Red/RedSemi-rapid 32 Blue/BlueRapid 40 Black/BlackDouble-Crown 56 Black/RedAeration adjustmen

14Important safety requirementsThis hob must be installed in accordance with the Gas Safety(Installation and Use) Regulations (Current Edition) and th

15CLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOVECLEARANCES REQUIREDWHEN FITTING THE GAS HOBWITH A COOKER HOOD ABOVEInstallati

16A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264this book be ignored.On the end of the shaft, which includes the GJ 1/2" threaded elbow,

1783047055 min.860500FO 2407Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob

18ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must betaken in designing th

19Building inFitting the hob to the worktopBefore fitting the hob into thecut out, a sealing gasketsupplied with the hob must befitted to the edge of

2Important Safety InformationYou MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Ca

20Electrical connectionsAny electrical work required to install this hob should be carried outby a qualified electrician or competent person, in accor

21Permanent ConnectionIn the case of a permanent connection, it is necessary that you installa double pole switch between the hob and the electricity

22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x1 scale and adjust zero if necessary.— Test leads from

24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

25CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

26Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gasbut can be converted for use with buta

3● When in use a gas cooking hob will produce heat and moisture in theroom in which it has been installed. Ensure there is a continuous airsupply, kee

4ContentsImportant Safety Information... 2Instructions for the User...

5This appliance is manufactured according tothe following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition.G

61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Double-crown Burner5. Auxiliary Burner6. Control knob for back left burner (semi-rapid)7. Control kn

7HOB BURNERSTo light a burner, turn the relevant control knob anticlockwise to themaximum position ( ), then push it down to ignite the burner.Upon, i

8Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s

9Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local AEG Service Force Centre